1. ±5% Is Not a Slogan. It Is a Set of Contract Numbers.
AEC and optical module paddle cards often carry ±10% impedance tolerance in the subtractive spec. By contrast, mSAP specs often state ±5%. That five-point gap means three things on the shop floor. Первый, the sidewall moves from a trapezoid to a near-rectangle. Второй, etch compensation must follow a board shop formula, not a rule of thumb. Third, shipment must include coupon TDR data from the same panel.
Industry design guidance commonly cites roughly 5–7% manufacturing tolerance for 50 Ω lines. IPC-2141A provides the controlled-impedance design framework. Более того, 224G and 112G SerDes discussions often point to ±3% to ±5% impedance precision for mSAP. That range applies to selected layers, not to every layer by default. Поэтому, the contract value of mSAP lies in three questions. Which layers use it? What compensation rule drives the artwork? What data proves acceptance?
2. When to Move from Subtractive to mSAP: Judge by Bottlenecks, Not by Frequency Alone
224G and 448G do not force mSAP by themselves. Вместо, they raise sensitivity to linewidth deviation and sidewall shape near Nyquist. FineLine and similar field-solver studies rank linewidth, layer spacing, and Dk as major factors. Copper thickness and solder mask rank as minor factors. The sidewall edge angle (W1−W2) is secondary, yet a subtractive trapezoid cannot default to a rectangle in simulation.
На практике, three bottleneck tiers guide the decision.
Уровень 1: Subtractive still works. L/S stays roughly above 50 мкм. The outline is loose. Differential pair spacing is not crowded. The impedance contract can still accept a ±10% narrative. Conventional subtractive HDI is enough.
Уровень 2: Subtractive falls short, so key layers use mSAP (гибридный). L/S enters the 25–50 µm band. Differential pair spacing is insufficient under a fixed outline. A near-rectangular section is needed to hold impedance. Eltek process tables list mSAP at 25/25 µm and subtractive at 50/50 мкм. Head:Foot also moves from (1−2/3 CuT):1 for subtractive toward ≈1:1 for mSAP and SAP. At this tier, full-layer buildup is unnecessary. Apply mSAP only to DSP/ASIC breakout and dense differential escape layers. Keep power, земля, and sparse signal layers on subtractive processing. This hybrid approach delivers the best cost-performance balance for paddle cards.
Уровень 3: Full-layer or near-full-layer mSAP. Multiple L/S locations drop below 25 мкм. Microvia stacking, pad escape, and pair spacing crowd together. The contract explicitly requires ±5% and a coupon for every layer. На этом этапе, ask the поставщик печатных плат about capacity and lead time before discussing slogans.
One boundary must remain clear. Unimicron FCBGA roadmaps list Core Layer MSAP at 12/16 мкм. Uyemura UHDI narratives mention 2/2 мкм. Both belong to the Подложка ИС and package substrate context. They are not default delivery standards for a paddle card. Поэтому, the SOW must prohibit citing FCBGA or ABF substrate L/S as module board acceptance criteria.
3. Etch Compensation: Artwork Linewidth Does Not Equal Finished Linewidth
mSAP adds copper only at circuit locations. A flash etch still removes the seed copper. The seed removal step eats spacing and rewrites linewidth.
Glickman gives the governing relationship:
Etch distance = foil thickness (minus cleaning oxidation) + electroless copper thickness + foil tooth + safety margin
Finished minimum space ≈ LDI minimum linewidth + 2 × etch distance
Например, assume an etch distance of 5.5 µm and an LDI minimum line of 10 µm on the space side. The finished space then reaches about 21 мкм. Наоборот, the artwork must draw that space at 10 µm under the compensation rule. Only then does the finished space reach 21 мкм. The product and the coupon on the same panel must share one compensation set. В противном случае, TDR data will diverge from the physical board.
Seed copper source also belongs in the spec. mSAP usually starts with a base Cu foil and 0.3–1.5 µm electroless copper. SAP typically uses no foil, больше, чем 1 µm electroless copper, and a higher adhesion and cost tier. A verbal claim of “full-layer build-up” fails DFM review when it omits the foil-seed versus pure-electroless distinction. Тонкий, low-roughness foil plus uniform plating and etching keeps etch distance under control.
4. Hybrid Stack-Up: Material Grade Is Not Process Capability
A common misreading treats Megtron 7, М6, or M8 low-loss material grades as automatic equivalents of mSAP. Фактически, material selection covers Dk, Дф, and copper foil roughness. Process selection covers linewidth formation. The spec must list them separately.
A hybrid stack-up table should contain at least five columns. Add a note: “Example only; final values require board shop sign-off.”
| Слой | Процесс | L/S target | Impedance target | Фольга / материал |
|---|---|---|---|---|
| L2 differential escape | Мсап | 25/25 мкм | 90 Ом ±5% (coupon required) | ХВЛП + specified Dk/Df grade |
| L3 power | Subtractive | Per current | - | Standard foil |
HVLP foil is no longer optional at 224G and 448G. В 56 ГГц, copper skin depth is about 0.28 мкм. When surface roughness Rz approaches that skin depth, the current path lengthens and conductor loss rises sharply. Based on Hammerstad-Jensen engineering estimates, HVLP with Rz = 4 µm adds roughly +40–60% extra loss at 56 ГГц. HVLP4 with Rz = 1.5 µm adds roughly +10–15%. В 25 ГГц, standard foil with Rz ≈ 10 µm adds about 0.8–1.2 dB/inch more loss than HVLP with Rz ≈ 2 мкм. Следовательно, copper foil roughness is a hard line item in the insertion-loss budget, not a material preference.
5. Cross-Section and TDR: No Coupon Data, No ±5% Claim
Three steps turn ±5% into acceptance.
Шаг 1: Cross-section checks rectangularity and top/bottom linewidth. Even a near-rectangular mSAP section needs photo-based top and bottom linewidth verification. Do not default to a vertical wall and thereby erase the subtractive trapezoid. IPC-6012 Класс 3 defines microsection acceptance for coupons and sections. A common shop rule keeps the section plane within 10% of the hole diameter. The SOW must state the sampled layers and section criteria. Процесс АОИ linewidth measurement reflects process capability. It cannot replace shipping cross-sections and TDR.
Шаг 2: TDR follows IPC-TM-650 Method 2.5.5.7. This method is the standard time-domain reflectometry method for печатная плата характерный импеданс. It calls for a 50 Ω TDR unit with uncertainty ≤ ±0.5 Ω. Common coupon practice calls for at least one coupon per panel, with two preferred. The minimum trace length is 150 мм (6 в). The default tolerance is ±10% unless the design file states otherwise. When the contract states ±5%, it must also state layer, reference plane, solder mask condition, TDR rise time, and window. Более того, the coupon and the product must share the same panel.
Шаг 3: Reflow and thermal cycling follow project rules, not slogans. Glickman’s 200 µm pitch work used 10× lead-free reflow plus air/liquid thermal cycling as a reference. MSA does not mandate that level. Many OEMs require 6×, while 10× serves as an engineering safety factor. The SOW should state microvia diameter, stacked-via layers, and whether a 6× or 10× reflow report is required.
6. DFM and Contract Fields: Make ±5% Buyable and Auditable
The following fields fit directly into review minutes and RFQs. They also form the checklist for qualifying an mSAP PCB supplier. Each field should return a signed response.
| Field | Required content |
|---|---|
| Процесс | Subtractive / Мсап / SAP; full-layer or layer list |
| Target L/S | мкм; отметка “shop capability” или “project target” |
| Artwork compensation | Etch distance or board shop formula; who edits Gerber |
| Seed copper | Foil thickness range + electroless copper thickness range |
| Импеданс | Nominal, терпимость, слой, reference plane, solder mask condition, coupon requirement (TDR per IPC-TM-650 2.5.5.7) |
| Материал | Grade + foil type (HVLP/VLP, и т. д.); substrate L/S must not replace paddle card criteria |
| Микровия | Диаметр, stacked layers, 6×/10× reflow report requirement |
| Lead time and panel | Written quote governs |
| Prohibited item | FCBGA/ABF substrate L/S must not serve as delivery standard |
| Safety standard | UL 796 remains the relevant printed wiring board safety standard; state flammability class in the SOW |
At the inquiry stage, send the stack-up table, impedance table, coupon layers, and acceptance criteria to the board shop for DFM sign-off. This step produces a more executable and auditable quote than a one-line request for “mSAP.” mSAP costs roughly 1.5–2.5× subtractive processing. A hybrid strategy keeps that multiplier on critical layers instead of spreading it across the whole board.
Заявление об источнике данных
- МПК-2141А, Design Guide for High-Speed Controlled Impedance Circuit Boards: controlled-impedance design framework; industry practice often cites roughly 5–7% manufacturing tolerance for 50 Ω lines.
- IPC-TM-650 Method 2.5.5.7: standard TDR method for PCB characteristic impedance; 50 Ω TDR unit with uncertainty ≤ ±0.5 Ω.
- IPC-6012 Класс 3: coupon and microsection acceptance requirements; common shop rule keeps the section plane within 10% of hole diameter.
- UL 796: UL safety standard for printed wiring boards; flammability and thermal requirements remain project-specific.
- Glickman and Eltek mSAP process data: etch distance formula, Мсап 25/25 µm example, Head:Foot ≈ 1:1, seed copper 0.3–1.5 µm.
- HVLP copper foil roughness and loss estimates: Rz = 4 µm HVLP adds roughly +40–60% extra loss at 56 ГГц; Rz = 1.5 µm HVLP4 adds roughly +10–15%; в 25 ГГц, standard foil adds about 0.8–1.2 dB/inch more loss than HVLP.
- Industry statements on 224G/448G mSAP impedance precision: roughly ±3% to ±5%; гибридный “critical-layer-only mSAP” is a common industry practice.
- mSAP cost multiplier versus subtractive processing: roughly 1.5–2.5×.
